“roll forming machine”目录存档

Roof Forming Machine

2009年08月24号，星期一

Roof-wall-panel-roll-forming-machine

1.roof forming machine

specification:

(1).raw material scale(mm):1000mm~1250mm×0.25~0.7mm×L

(2).rolling depression speed: 17~20M/min

(3).roller number:18~26 couple (according to specific panel shape)

(4).roller material:adopt high quality 45#steel with chromizing on surface

(5).main axletree material:adopt high grade 45#steel finish machining

(6).power of the main pump:4KW

(7).pressure of hydraulic station: 10~12 Mpa   .

(8).electrical control system: Using PLC Control the quantity, length automatically, touch screen

(9).equipment shape size:approximately 10000mm×1600mm×1200mm

(10).equipment total weight:approximately 7~10 Tons(according to specific panel shape)  .

2.roof panel forming Machine

Components:
(1) Manual Un-coiler————————————————1 set
(2) Roll-Forming M/C———————————————–1 set
(3) Hydraulic Cutting————————————————1 set
(4) PLC Control System——————————————1 set
(5) Product Rack (un-powered)———————————1 set
3.Technical Specification:
(1) Manual Un-coiler:

Un-powered; Load capacity = Max.5Tons;
(2) Roll-Forming machine:
About 18steps to form; Material of Roller: 45# steel with chromizing on surface
Voltage:380V/50Hz; Main line speed:8~12 m/min;
(3) Hydraulic Cutting:
Stop to cut————>Post cut,
Cutting tool material: Cr12, Heat treatment
(4) PLC Control System:
Using PLC Control the quantity, length automatically, LCD screen,
(5) Product Rack (UN powered)
4.Hydraulic Un-coiler:
Hydraulic system to expand coil inner hole;
Frequency Inverter to regulate turning speed,
Automatic stop device;Load capacity = Max.5Tons;
5.Material:
(1) Coil Width: 1000mm~1250mm
(2) Suitable Coil Thickness: 0.25~0.7mm

roof forming machine,roof panel forming machine,wall panel forming machine,roll forming machine,forming machine,roll forming machinery

标签：,
发布在 roll forming machine | 没有评论 »

Sandwich Panel Line

2009年08月24号，星期一

The technical plan made below includes the following parts: hydraulic powered uncoiler, film coverin

PU Sandwich Panel Forming Machine includes the following parts:

hydraulic uncoiler,film covering equipment,roll forming machine,preheating oven,polyurethane forming system,double belt conveyor,double belt heating device,cutting device,automatic stacker.

Sandwich Panel Parameters:
1.Min.cutting length: 3 meters
2.Max.stacking length: 15m
3.Panel width: 1000mm
4.Panel thickness mini thickness: 40mm(corrugated sandwich panel)
50mm(wall panel)
max.thickness: 150mm(exclude corrugated sandwich panel)

The technical plan made below includes the following parts: hydraulic powered uncoiler,
film covering equipment, roll forming machine, preheating oven, polyurethane
foaming system, double belt conveyor, double belt heating device, cutting device,
automatic stacker, packing system.
Sandwich Panel Spec. Min. cutting length 3 meters Max. stacking length 15mPanel width 1000mmPanel thickness Mini thickness: 40mm (corrugated sandwich panel) 50mm (wall panel)Max. thickness: 150mm(exclude corrugated sandwich panel) Steel Sheet Spec Thickness 0.4-0.8mm(the don”t have any corrugation ,the width
accuracy need to be +/-2mm)
Width 1250mmMax. coil weight 5tons Inner Dia. of coil 508mm, 610mm Whole Line SpecWorking speed max. 7m/min (adjustable)Total length about 115mWorking height 1200mm (height of panel coming out)Pressure for foaming 150-200 barDouble belt conveyor 21mControl mode PLCTotal power about 300KwPower required 380V/3phase/50HzControl voltage 24V 110V 220vAir pressure 0.7Mpa (for buyer to prepare)

标签：, ,
发布在 roll forming machine | 没有评论 »

Sheet Forming Machine

2009年08月24号，星期一

Roof-wall-panel-roll-forming-machine

Sheet forming machine,panel machine,forming sheet has good quanlity ,low price,,accurate measurement,high starting point.

Sheet forming machine,panel machine,forming sheet

Main technical parameters:

(1)Diameter of principal:70mm

(2)Sprocket:P-25.4

(3)Forming speed:8m/min

(4)Main motor power:7.5kw

(5)Hydraulic station power:4kw

(6)Yield strength:32MPa

(7)Electric controlling system: automatic computer control system

(8)Material of roll:45 # steel hard chrome plating

(9)Forming station:22

(10)Thickness:≤1mm

(11)Installation dimension about(L*W*H):11*1.5*0.8m

(12)Equipment parts: roll forming system, hydraulic cutter, hydraulic station, electric controlling system, counter, product support.

标签：,
发布在 roll forming machine | 没有评论 »

Roll Bending Machine

2009年08月24号，星期一

Its suitable for bending and modelling the metal plates.Through it the plate can be rolled innto the round and are workpieces and the cone ones within the specified ranges.This machine has the functions of prebending plate at both ends and the merits of small remained sides and high efficiency.And the metal plates can be rough levelled throughit.This roll is widely used in petroleum,chemical industry,boilers metalstructure,shipbuilding,machine manufacture and other trades.

标签：,
发布在 roll forming machine | 没有评论 »

Metal Forming Machine

2009年08月24号，星期一

rool forming machine

1.45#,Φ80mm.

Main axle material quality: 45# steel quenching and retemperingtreatment, outer diameter Phi 80mm.

2.1)Cr12HRC60-62

Roller material: 1) Cr12 chrome steel quenching processing HRC60-62°(selects and    matches)

2)GCR15HRC58-60°.

Roller material: 1) Cr12 chrome steel quenching processing HRC60-62°(selects and matches)

3.Equalization roller group number: 5 rollers equalization

4.Main roller group number: 12 groups of main rollers, 2 groups offeeding rollers, 6 groups of sides rollers.

5.Main electrical machinery power: 15KW

6Rolling speed: 8-12 meter/minute

7,.Shuts off the system: Uses the advanced hydraulic pressure actuation,after takes shape automatically decides the ruler to shut off.Invariable Does not have the waste material, the safety coefficient highercharacteristic. (Main engine stops shuts off)

8,.blueprint about, but around wilfully establisheswilfully adjusts.

9.Bit, drift material: Cr12, quenching processing 60-62°.

10.Electrically controlled system: Entire machine uses PLC, the frequencychanger control, revolves straightens

11.Main engine outlook size: Approximately long 10.5M× width 1.7M× high1.2M

标签：, ,
发布在 roll forming machine | 没有评论 »

Tile Forming Machine

2009年08月24号，星期一

Roof-wall-panel-roll-forming-machine

Introduction 
The line consists of decoiler, sheet guiding equipment, roll forming section, punching equipment, cutter, supporter, hydraulic system, control system. The tile can be widely used in garden factory, resort, pavilions, hotel and villa, exhibition hall, vacationland. 

Main Technical Parameters 
1. Material Spec: Q235 or 34 KSI; Thickness: 0.4 mm to 0.6 mm 
2. Hydraulic decoiler Max. Capacity: 5000kgs 
3. Controlling system: PLC 
4. Main machine power: 7.5kw; 
Hydraulic station power: 5.5kw 
5. Step length: 200-350mm 
Step height: 14mm 
6. Working speed: 3-4m/min 
7. Type of cutting: Roll-formed and length-set cutting 
8. Power: 380V/3ph/50Hz or at the buyer’s requirement

标签：, ,
发布在 roll forming machine | 没有评论 »

PURLIN FORMING MACHINE

2009年08月24号，星期一

标签：,
发布在 roll forming machine | 没有评论 »

PURLIN ROLL FORMING MACHINE

2009年08月24号，星期一

Interchangeable-C-Z-machine

Interchangeable-C-Z-machine-TP

This machine is full-automatically controlled by PLC,the whole hydrau-lic transmission,drive hydraulic oil jar carry out and shear through centre pump station towarde the hole,hydraulic pressure motor trans-mit power as main transmission,characteristic its reliable for to oper-ate steadily by hydraulicprdssure,Shear towards hole precision high,high output,low energy consumption,Section geometry form rule of the notch,Its hydraulic pressure trausmission ,two sets of rectification correct and fit,the cut-off have a national patent.

  • Main motor prwer:30KW
  • Roll stand:16
  • Thickness:1.5-3.0mm
  • Material of cutter:Cr12
  • Spec:140-300
  • Waist height:50-90

The C-shaped or Z shape purlines formed by purlig forming machine have excellent anti-bending property and are easy to install. They are widely used as the supporter of roof and wall in large-scale and mid-scale construction, such as factory, warehouse, garage, exhibition center, cinema, theatre, garden and so on.
Machine’s components: One Purline Forming Machine can produce many sizes of purline. Purlin forming machine mainly consists of uncoiler, coil sheet guiding device, flattening device, roll forming system, punching equipment, cutting equipment, hydraulic station, PLC controlling system and support table.

  • Suitable Material: Cold-rolled steel strip and heat-treated galvanized steel strip;
  • Forming speed: about 10-12m/min
  • Power Requirement Main motor power: 15 Kw(Depend on final design)
  • Hydraulic station power: 5.5Kw (Depend on final design)
  • Uncoiler’s loading capacity Max. Capacity: 5000kgs (can be increased to be 10T)
  • Controlling system: Mitsubishi PLC & converter
  • Voltage: 380v 3 phase 50Hz or as per the customer’s requirement
  • Machine’s size: about 1800mm×2400mm×1400mm (Depend on final design)
  • Machine with CE certificate.

标签：,
发布在 roll forming machine | 没有评论 »